New install on Squak Mountain Issaquah and unable to find any signal on Tiger Mountain. I’m 3.5 miles away west and a little north of the tower on Tiger. Clear line of sight. Please validate with the tower picture attached. Installed the following: MikroTik mANT30 PA parabolic dish antenna 5GHz 30dBi MTAD-5G-30D3-PA Mikrotik BaseBox 5 RB912UAG-5HPnD-OUT 5GHz Outdoor Wireless AP Gigabit USB OSL4 Questions: Q1) Is the antenna tower on the right in the picture the right site? Q2) Is the dish assembled correctly? See picture. Q3) I was watching the signal strength on the routerboard while running "/interface wireless scan 0”. Nothing showed up on the terminal session and no signal strength LED’s lit up. I moved it left to right and adjusted azimuth each time I stopped. Q4) How long should you wait to acquire the signal between each time you move it? Q5) Is there anything like the signal strength tones aiming a DirecTV dish? Q6) Any other ideas. My exported configuration is below and I’ve successfully completed every step listed here: https://hamwan.org/Standards/Network%20Engineering/Client%20Node%20Configura... <https://hamwan.org/Standards/Network%20Engineering/Client%20Node%20Configuration.html> Thanks for your help! -Paul KK7AMW [admin@KK7AMW-Issaquah] > export # sep/08/2021 16:57:46 by RouterOS 6.48.4 # software id = H1Z0-P9F3 # # model = 912UAG-5HPnD /interface wireless set [ find default-name=wlan1 ] band=5ghz-onlyn country=no_country_set disabled=no frequency-mode=superchannel radio-name=KK7AMW/Issaquah-Tiger scan-list=HamWAN ssid=HamWAN \ wireless-protocol=nv2 /interface list add name=WAN add name=LAN /interface wireless channels add band=5ghz-onlyn comment="Cell sites radiate this at 0 degrees (north)" frequency=5920 list=HamWAN name=Sector1-5 width=5 add band=5ghz-onlyn comment="Cell sites radiate this at 120 degrees (south-east)" frequency=5900 list=HamWAN name=Sector2-5 width=5 add band=5ghz-onlyn comment="Cell sites radiate this at 240 degrees (south-west)" frequency=5880 list=HamWAN name=Sector3-5 width=5 add band=5ghz-onlyn comment="Cell sites radiate this at 0 degrees (north)" frequency=5920 list=HamWAN name=Sector1-10 width=10 add band=5ghz-onlyn comment="Cell sites radiate this at 120 degrees (south-east)" frequency=5900 list=HamWAN name=Sector2-10 width=10 add band=5ghz-onlyn comment="Cell sites radiate this at 240 degrees (south-west)" frequency=5880 list=HamWAN name=Sector3-10 width=10 /interface wireless security-profiles set [ find default=yes ] supplicant-identity=MikroTik /snmp community set [ find default=yes ] addresses=44.24.240.0/20 name=hamwan /system logging action set 3 remote=44.24.244.8 /interface list member add interface=wlan1 list=WAN add list=LAN /ip address add address=192.168.86.53/24 interface=ether1 network=192.168.86.0 /ip dhcp-client add disabled=no interface=wlan1 /ip dns set servers=192.168.86.9 /ip firewall mangle add action=change-mss chain=output new-mss=1378 protocol=tcp tcp-flags=syn tcp-mss=!0-1378 add action=change-mss chain=forward new-mss=1378 protocol=tcp tcp-flags=syn tcp-mss=!0-1378 /ip route add distance=1 gateway=192.168.86.1 /ip service set telnet disabled=yes set ftp disabled=yes set www disabled=yes set ssh port=222 set api disabled=yes set api-ssl disabled=yes /snmp set contact="#HamWAN-Support on irc.freenode.org" enabled=yes location=47.516944,-122.0452 /system clock set time-zone-name=America/Los_Angeles /system identity set name=KK7AMW-Issaquah /system logging add action=remote topics=info add action=remote topics=warning add action=remote topics=error /system ntp client set enabled=yes primary-ntp=44.24.244.4 secondary-ntp=44.24.245.4 /system routerboard settings set boot-device=try-ethernet-once-then-nand [admin@KK7AMW-Issaquah] >
