Thanks Bart! I I ran the client setup page verbatim and this was the results with the exception of Winbox and Port222. I wanted to stick with Winbox until I was finished with the initial setup. I just received a new computer this afternoon so will move the whole set up along with all Ham related programs over to it. On Fri, Nov 1, 2019 at 3:36 PM Bart Kus <me@bartk.us> wrote:
Yes, much better. I also noticed a problem on the HamWAN side, where that sector was configured for only 5MHz service instead of our normal 10MHz. I've changed the sector config, and you should be getting twice the bandwidth now.
I tried to run a speed test, but noticed your bandwidth-server was still set to require authentication, so I've logged into your modem and turned that off:
[eo@K7ITE-Lookout] > /tool bandwidth-server set authenticate=no
I also noticed you still have an "admin" account. If it's not properly password protected, this may be dangerous now that your modem is on the Internet. I have left it untouched.
I also noticed you have the "winbox" service running. This is also dangerous, as it's full of exploits. I have left it untouched, but you should probably disable it. (/ip service disable winbox) We should update the website instructions to disable this by default.
I also noticed your ssh is on port 22. This will get more hacking attempts than port 222. You can change it with /ip service set ssh port=222.
With the bandwidth-server available on your end, I ran a speed test from the sector to your modem:
[eo@Lookout-S2] > /tool bandwidth-test 44.25.143.94 duration=30s direction=transmit status: running duration: 29s tx-current: 38.4Mbps tx-10-second-average: 35.6Mbps tx-total-average: 37.5Mbps random-data: no direction: transmit tx-size: 1500 connection-count: 20 local-cpu-load: 20% remote-cpu-load: 28%
[eo@Lookout-S2] > /tool bandwidth-test 44.25.143.94 duration=30s direction=receive status: running duration: 29s rx-current: 40.8Mbps rx-10-second-average: 41.7Mbps rx-total-average: 35.7Mbps lost-packets: 1285 random-data: no direction: receive rx-size: 1500 connection-count: 20 local-cpu-load: 21% remote-cpu-load: 27%
This is the performance you can expect from a 10MHz MIMO link that has good signal.
The current-distance is reported in km, not miles. It's not round-trip distance, just physical distance between the modems. There is a separate metric for round-trip-time, which is measured in microseconds: tdma-timing-offset=202. You can do the speed-of-light math to get a more precise distance than the 1km granularity reported by the "current-distance" field.
--Bart
On 11/1/2019 3:18 PM, Ric Merry wrote:
tx-rate: 6.5Mbps-5MHz/2S rx-rate: 3.2Mbps-5MHz/1S ssid: HamWAN bssid: 74:4D:28:57:F6:BA radio-name: Lookout-S2/WA7DEM signal-strength: -62dBm signal-strength-ch0: -64dBm signal-strength-ch1: -66dBm tx-signal-strength: -62dBm tx-signal-strength-ch0: -66dBm tx-signal-strength-ch1: -64dBm noise-floor: -124dBm signal-to-noise: 62dB tx-ccq: 35% rx-ccq: 19% authenticated-clients: 1 current-distance: 32
Mo' betta? Is current distance miles in both send and receive (round trip)?
On Fri, Nov 1, 2019 at 3:06 PM Bart Kus <me@bartk.us> wrote:
No, you're missing an entire chain of the radio (ch1). Do this to enable both chains:
/interface wireless set 0 rx-chains=0,1 tx-chains=0,1
--Bart
On 11/1/2019 2:55 PM, Ric Merry wrote:
I climbed back up the ladder to do some fine tuning (thanks for the advice here) Luckily I could remotely view my computer with my cell phone thus saving me the cost of a divorce attorney had I asked my wife to help me when she gets home from work. ;) These are my results, I can do more but for now, how do they look?
signal-strength: -66dBm signal-strength-ch0: -66dBm tx-signal-strength: -67dBm tx-signal-strength-ch0: -67dBm tx-signal-strength-ch1: -89dBm noise-floor: -123dBm signal-to-noise: 57dB tx-ccq: 88% rx-ccq: 70% authenticated-clients: 1 current-distance: 32
Funny things is that thee are about where I started. Elevation is the more difficult adjustment with the brackets provided. I may end up modifying those.
_______________________________________________ PSDR mailing listPSDR@hamwan.orghttp://mail.hamwan.net/mailman/listinfo/psdr