- PSDR - mailman.hamwan.org

New to HamWan
by Phil Cornell 13 Mar '21

13 Mar '21

I am new to this part of the hobby. I have been a ham since 1978 and I am now very involved in ARES. I have a Winlink RMS Hybrid Gateway and I was looking for an alternative to my Comcast internet, then I found HamWan. I read as much as I could and decided to take the plunge. I purchased the recommended Microtik equipment and it is assembled, (I will be mounting the antenna next Wed). I was trying to use Winbox to setup the router and something happened. I am now locked out and can no longer connect to the router ("Incorrect user name or password"). I think I can reset the router manually at the board and start the configuration all over again with a new router config process but I need some help with some of the steps. Watching K7MM's video answered many of my questions but the reset is still a question in my mind. How is it done? What happens after I complete the configuration? How do I integrate this into my gateway station? Newbie is drowning in all the tech manuals and code!!! Phil Cornell W7PLC SHARES NCS590 Hybrid Gateway W7PLC TCARES VP

1 0

Connecting to Bellingham (Lookout)
by Scott Leaf 10 Mar '21

10 Mar '21

4 5

Connecting to Bellingham (Lookout)
by Scott Leaf 10 Mar '21

10 Mar '21

Hi all: I am new to this group and I tried to browse the previous threads to see if this was covered and did not see anything so if I missed it sorry. I have purchased the recommended Mikrotik radio and 30db dish, programmed it and I do see the HamWan channels in the Scan list. Yes I have the international version. I am shown in the HamWan coverage area according to the coverage map and I can in fact see Lookout Mtn from where I am at 120M elevation here in Maple Ridge BC. Used to connect to the 900 Mhz repeater there with a handheld on low power from here. Don't think the QTH is the problem. Took the dish and laptop up to do a ballpark test before permanent install but I am getting no signals on the HamWan channels. When I switch to Wifi I get dozens and dozens so it is working. Rotated dish 90 degrees just in case I had the polarity wrong, still nothing. Is Lookout still broadcasting North on 5920? Suggestions please, Scott VA7SL

1 0

Connecting to Bellingham (Lookout)
by Scott Leaf 10 Mar '21

10 Mar '21

1 0

Re: [HamWAN PSDR] PSDR Digest, Vol 97, Issue 2
by Rob Martin 06 Mar '21

06 Mar '21

If anyone is going up to Rattlesnake or Capital PEAK, I have a very simple task I would like someone to perform on my behalf. On both sites, there was a problem with my remote AC power switch. I would like someone to take a new part to the site, and swap out the one that is there already. I have new switches ready to go. Thanks. RobK7QJ On Saturday, March 6, 2021, 12:00:17 PM PST, psdr-request(a)hamwan.org <psdr-request(a)hamwan.org> wrote: Send PSDR mailing list submissions to psdr(a)hamwan.org To subscribe or unsubscribe via the World Wide Web, visit http://mail.hamwan.net/mailman/listinfo/psdr or, via email, send a message with subject or body 'help' to psdr-request(a)hamwan.org You can reach the person managing the list at psdr-owner(a)hamwan.org When replying, please edit your Subject line so it is more specific than "Re: Contents of PSDR digest..." Today's Topics: 1. Re: Rattlesnake DNR shack is down (Bart Kus) 2. Re: Rattlesnake DNR shack is down (Fred Moses) ---------------------------------------------------------------------- Message: 1 Date: Sat, 6 Mar 2021 09:46:15 -0800 From: Bart Kus <me(a)bartk.us> To: Puget Sound Data Ring <psdr(a)hamwan.org>, Stephen Kangas <stephen(a)kangas.com>, netops(a)hamwan.org Subject: Re: [HamWAN PSDR] Rattlesnake DNR shack is down Message-ID: <1947e401-ede2-3fde-387d-8bdec70cf98c(a)bartk.us> Content-Type: text/plain; charset="utf-8"; Format="flowed" Stephen and I went to visit Rattlesnake yesterday to figure out what's wrong. The building had power, but the new UPS was powered off. Its network control card had a light, indicating it was alive, just no network to link to. I pulled the 120V plug, and a relay clicked but UPS did not change state. I restored 120V power, and a relay clicked but UPS did not change state. I unplugged/replugged the display, and it flashed all LEDs and went back to indicating off state (no LEDs). Finally I pressed power button and everything powered back up normally. I suspected the UPS software had been unintentionally set to stay powered off after it ran out of battery juice, and then power was restored. I checked the settings thoroughly, and everything looks like it was set to tell the UPS to power back on after it had shut down from battery exhaustion. Only a test will verify this is indeed working as intended though. I started setting up event notification from the UPS and making sure our management system can monitor it too, and noticed something really weird. *The defaults in the UPS software apparently leave a write-enabled SNMP account with the default credentials of "private", with access allowed from anywhere (IP 0.0.0.0).* I'm now wondering if someone intentionally sent an SNMP write command to some OID that told the UPS to power off? Does anyone have experience with APC UPSes that can verify these insane defaults and that there is some OID that can command the UPS to power off? SNMP write access has been disabled on both new UPSes now, and firewall rules installed to prevent general internet access. --Bart On 2/28/2021 3:37 PM, Bart Kus wrote: > No, the DMR repeater is in the smaller shack, which has its own > backbone feed from Baldi. That half of Rattlesnake is alive. > > --Bart > > > On 2/28/2021 12:28 PM, Stephen Kangas wrote: >> If the DNR shack had power out, wouldn't that also break the inet >> link for the AF7PR DMR repeater inet linkage that is hard-wired from >> the smaller secast shack? That repeater is still linked (just tested >> it via Parrot). >> >> Stephen W9SK >> >> >> -----Original Message----- >> From: PSDR <psdr-bounces(a)hamwan.org> On Behalf Of Bart Kus >> Sent: Sunday, February 28, 2021 12:23 PM >> To: netops(a)hamwan.org; Puget Sound Data Ring <psdr(a)hamwan.org> >> Subject: [HamWAN PSDR] Rattlesnake DNR shack is down >> >> It looks like the DNR building is completely without power. I tried >> to check if UPS2.Rattlesnake was on battery, but the DHCP server is >> in the DNR building so the UPS lost its lease. I'm about to head out >> here for something else, but maybe someone can stand up a temporary >> DHCP to get the UPS back online and check battery status. >> >> --Bart >> >> _______________________________________________ >> PSDR mailing list >> PSDR(a)hamwan.org >> http://mail.hamwan.net/mailman/listinfo/psdr >> >> _______________________________________________ >> PSDR mailing list >> PSDR(a)hamwan.org >> http://mail.hamwan.net/mailman/listinfo/psdr >

1 0

Rattlesnake DNR shack is down
by Bart Kus 06 Mar '21

06 Mar '21

It looks like the DNR building is completely without power. I tried to check if UPS2.Rattlesnake was on battery, but the DHCP server is in the DNR building so the UPS lost its lease. I'm about to head out here for something else, but maybe someone can stand up a temporary DHCP to get the UPS back online and check battery status. --Bart

3 4

Buck Mt
by Jamie Hughes 28 Feb '21

28 Feb '21

Good Evening All, Is Buck a Cell site that is active for connections. I don't see it listed on the Sites page. Jamie Hughes WA7JH Phone: (360) 340-8886<tel:+13603408886>

2 1

Re: [HamWAN PSDR] Support needed
by Jamie Hughes 27 Feb '21

27 Feb '21

Sorry to pester, So I am now on step 22 and I get the error listed, however, I am not sure what to do to overcome the error as described in the notes under the step. Here are the results from running the commands as listed: [admin@KC7Z-East_Bremerton-Gold_Mt] /ip dhcp-client> /interface bridge port print Flags: X - disabled, I - inactive, D - dynamic, H - hw-offload # INTERFACE BRIDGE HW PVID PRIORITY PATH-COST INTERNAL-PATH-COST HORIZON 0 ;;; defconf ether1 bridge yes 1 0x80 10 10 none 1 I ;;; defconf wlan1 bridge 1 0x80 10 10 none [admin@KC7Z-East_Bremerton-Gold_Mt] /ip dhcp-client> Jamie Hughes WA7JH Phone: (360) 362-4575 -----Original Message----- From: Steve - WA7PTM <psdr-list(a)aberle.net> Sent: Saturday, February 27, 2021 16:54 To: Jamie Hughes - WA7JH <wa7jh(a)outlook.com> Subject: Re: [HamWAN PSDR] Support needed See the notes below the command. I've seen that before, but don't recall how I solved it. Sorry. Steve Jamie Hughes wrote on 2/27/21 4:49 PM: > Well, > > Step 22 presents this error: > failure: can not run on slave interface > > > Jamie Hughes > WA7JH > Phone: (360) 362-4575

2 2

Support needed
by Jamie Hughes 27 Feb '21

27 Feb '21

Good Evening, While working on step 21, I got this error: failure: only regulatory-domain mode allowed for this country According to my order and my box the unit is an International Unit. Ideas? Jamie Hughes WA7JH Phone: (360) 362-4575<tel:+13603624575>

2 3

KC7Z
by Jamie Hughes 27 Feb '21

27 Feb '21

Good Saturday Evening, The Kitsap County Amateur Radio Club is in process of establishing two links to a tower site located in East Bremerton. We plan to target Gold Mt with one and then Columbia or VA in Seattle with the other for redundant links. We would love to have a net 44 address with no port restrictions in order to host devices at the site. I would love some help on identifying the resources required to support both links and other devices at the site. Thanks, Jamie Hughes WA7JH Phone: (360) 362-4575<tel:+13603624575>

2 1